Iscar Recently Releases A Variety Of Brand New Lines To Increase Their Family Of Milling Cutters
Iscar adjustable Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially helpful in the automotive and aerospace industries.
The cutters are dynamically balanced and especially developed to work with polycrystalline diamond (PCD) or cubic boron nitride (CBN) inserts. The use of these inserts will greatly increase surface finish. Standard HSM-rated HELIMILL carbide inserts will additionally work with these tools. Internal coolant holes allow cooler cutting face with enhanced chip expulsion and built-up edge resistance. The insert pockets feature a flexible rear stopper, allowing for axial positioning of the cutting edge within 0.002 mm.
Iscar's endmills designated E90AD are obtainable with HSK A63 shanks in 4 diameters starting from 25 to 50 mm. Iscar Facemills designated F90AD cover the 50 to 80 mm diameter range are offered in 4 sizes.
When utilized with Iscar HELIMILL carbide inserts, the adjustable high speed milling cutters deliver a fluid cutting action at low cutting forces. HELIMILL inserts' helical cutting edges slowly enter the work piece reducing the impact load on the cutting face.
CHATTERFREE Solid Carbide Endmills
Iscar is enlarging the extremely successful CHATTERFREE solid carbide 4 flute endmill family with the addition of smaller (3, 4 and 5 mm) and larger (25 mm) diameters. The new solid carbide endmills are used for roughing and finishing operations. Due to their variable pitch they showcase amazing chatter dampening capability. These endmills are an outstanding resolution for low power machines by increasing their material removal rate and reducing vibration. They can be employed for full slot machining of up to 2XD with solid carbide endmills.
Iscar's CHATTERFREE endmills increase material removal rate and reduce cycle time in most milling operations. Their special ground geometry provides remarkable surface finish and prolonged tool life, while machining at high material removal rates.
New ID5 PCD and IB85 PCBN Tipped Milling Inserts
Iscar is adding a completely new TANGMILL ID5 PCD wiper insert and 2 HELIMILL inserts tipped with IB85 PCBN, for machining cast iron and a broad range of hard-to-machine materials at high cutting rates. The new LNAR 1106PN-R-S-W ID5 PCD tipped wiper insert has a extraordinarily large frontal radius and sharp cutting edge. It provides a consistent clean-cut edge and outstanding surface finish of less than Ra 0.3 µm. Iscar's new HELIMILL insert ADKW 1505 PDER IB85 has an IB85 PCBN brazed tip and can be used on 90 distinct milling cutters for semi-finishing and finish machining on cast iron. The insert incorporates a 0.8 mm corner radius and a honed cutting edge (0.03 mm). It can be used on the conventional F90AD...-SFR or the E90AD ...-HSK63-S axially adjustable milling cutters.
By adjusting the axial position of the inserts, it is permissible to accomplish a 0.3-0.7 µm surface finish. IB85 is a fine grain polycrystalline cubic boron nitride grade. The compact grain size enables grinding a tremendously sharp cutting edge and achieving high surface quality, which provide excellent tool life. The IB85 grade can be used for machining a wide range of challenging to machine metal at high cutting rates and provides excellent tool life. IB85 contains 85% PCBN with Al Co and W binder.
It is a extraordinarily strong and tough material which can be utilized for heavy roughing and interrupted cuts. The array of materials covered by IB85 encompasses hardened and cast steel of over 45 HRc, grey and nodular cast iron, powder compacted and sintered metals as well as heat resistant alloys.
Related Articles
Resources
|
